G - Force A2000 - 040 Combo Accelerator Card REV 6 - Commodore Amiga - With GURU ROM
Item History & Price
Reference Number: Avaluer:7034724 | Compatible Brand: For Commodore |
Brand: GVP | Type: CPU/Processor |
G-Force A2000-040 Combo Accelerator Card REV 6 - Commodore Amiga
This is a GVP 68040 acellerator for the Commodore Amiga 2000. Besides the 33mhz CPU, it has an FPU, SCSI, Serial/Parallel ports and 4 SIMM slots for memory. This card has been fitted with a V6.11 GURU ROM that greatly increases SCSI speed and provides other benefits. The amount of installed RAM is unknown, I believe its 8-12MB.
This vintage accelerator was pulled from a working Amiga 2000, howe...ver the CPU fan had seized up. I removed it and cleaned the CPU. It's currently ready to have something else installed on it, and I would advise doing so before running this card longer than a few minutes. I did use it long enough to see the computer boot, then I shut it off. The card is also missing the external 25-pin SCSI bracket that plugs into the header on the card. Any sort of 25 pin port/ribbon cable should be able to be connected to this or you can just use the internal SCSI interface.
This card is sold strictly AS/IS, no returns or exchanges! Thanks for looking!
Some more information on this card (via the Amiga Hardware Database):
G-Force 040
Great Valley Products, USA
1992
Amiga
A2000
Interface:
CPU slot
Autoconfig ID:
2017 / 11, 255
processor:
68040 @ 33 MHz
memory:
four 64 pin SIMM sockets accept 64 MB RAM
supports only special 4 or 16 MB GVP SIMMs
SIMM sizes cannot be mixed
040 burst mode requires all four sockets to be filled up
Kickstart remapping
SCSI 2 DMA controller:
not Fast SCSI 2 - the same electronic as the GVP Series II controllers
no termination power is fed to the external SCSI connector - active termination must be used
50 pin internal SCSI header
DB25 external connector
RDB compatible
supported by Linux and NetBSD
I/O:
RS232 compatible 9 pin buffered serial port
614140 bps max transfer speed
Centronics parallel port
selectable IBM / Amiga compatible mode
notes:
32 bit expansion bus for the EGS 110/24 graphics board
This is a GVP 68040 acellerator for the Commodore Amiga 2000. Besides the 33mhz CPU, it has an FPU, SCSI, Serial/Parallel ports and 4 SIMM slots for memory. This card has been fitted with a V6.11 GURU ROM that greatly increases SCSI speed and provides other benefits. The amount of installed RAM is unknown, I believe its 8-12MB.
This vintage accelerator was pulled from a working Amiga 2000, howe...ver the CPU fan had seized up. I removed it and cleaned the CPU. It's currently ready to have something else installed on it, and I would advise doing so before running this card longer than a few minutes. I did use it long enough to see the computer boot, then I shut it off. The card is also missing the external 25-pin SCSI bracket that plugs into the header on the card. Any sort of 25 pin port/ribbon cable should be able to be connected to this or you can just use the internal SCSI interface.
This card is sold strictly AS/IS, no returns or exchanges! Thanks for looking!
Some more information on this card (via the Amiga Hardware Database):
G-Force 040
Great Valley Products, USA
1992
Amiga
A2000
Interface:
CPU slot
Autoconfig ID:
2017 / 11, 255
processor:
68040 @ 33 MHz
memory:
four 64 pin SIMM sockets accept 64 MB RAM
supports only special 4 or 16 MB GVP SIMMs
SIMM sizes cannot be mixed
040 burst mode requires all four sockets to be filled up
Kickstart remapping
SCSI 2 DMA controller:
not Fast SCSI 2 - the same electronic as the GVP Series II controllers
no termination power is fed to the external SCSI connector - active termination must be used
50 pin internal SCSI header
DB25 external connector
RDB compatible
supported by Linux and NetBSD
I/O:
RS232 compatible 9 pin buffered serial port
614140 bps max transfer speed
Centronics parallel port
selectable IBM / Amiga compatible mode
notes:
32 bit expansion bus for the EGS 110/24 graphics board